Which of the following is not the part of the bed? Explanation: All are the part of the bed. Tailstock is a sliding unit on the bed-ways of the lathe bed. Carriage is the part of the lathe which slides over the bed-ways.

Which of the following is not a part of lathe?

Explanation: Arbor is not a part of centre lathe.

Which one of the following is not a part of the centre lathe?

Explanation: . Arbor is not a part of centre lathe.

Which of the following is not the part of tailstock?

Which of the following is not the part of spindle? Explanation: All above mentioned are the parts of spindle. In tailstock, the spindle holds dead center. In headstock, the spindle is able to hold live center.

Which of the following is not true regarding the all gear drive *?

Explanation: This is false. All gear drive has internal webs for shaft bearing and some other purposes.

Jannie Monster Under the Bed Pretend Play Story for Kids

42 related questions found

Which of the following is not true for tailstock method *?

6. Which of the following is not true for tailstock method? Explanation: All the mentioned sentences are true except one which says that accurate setting of the offset is easy. Actually, accurate setting of the offset is difficult in this method.

Which of the following is not a part of automatic transmission?

6. Which of the following is not part of automatic transmission? Explanation: The automatic transmission consists of the epicyclic gearbox, torque convertor, and multi-plate clutch. The sliding mesh gearbox is a type of manual transmission.

Which one of the following is not the part of a shaper?

Explanation: Tailstock is NOT the part of a shaper. Tailstock is a part of Lathe.

What are the parts of tailstock?

The main parts of the lathe, all parts are bolted to the bed. It includes the headstock, tailstock, carriage rails and other parts. Carriage: The carriage is located between the headstock and the tailstock and contains apron, saddle, compound rest, cross slide and tool post.

Is widely used for machine bed?

Gray Cast Iron has extremely high damping capacity, and is therefore the preferred material for machine tool beds, tables, columns, etc. (as also engine cylinder blocks, for the same reason).

Which is not the type of Centre in lathe?

2. Which of the following is not the type of centre in lathe? Explanation: Only live centre and dead centre are there in lathe.

Which type of lathe is known as Centre lathe?

1. Which type of lathe is also known as centre lathe? Explanation: Engine lathe is also known as the centre lathe. This centre lathe is generally used for the production of cylindrical surfaces.

What is the lathe bed made of?

Cast iron is commonly used for machinery housings or base due to its damping characteristics. It is also known for holding its shape when it is subjected to contraction and expansion due to temperature fluctuations. Hence lathe bed is usually made up of cast iron.

Which of the following is not the type of lathe chuck?

7. Which of the following is not the part of four jaw chuck? Explanation: Body and shaft chunk key are the parts of three jaw chuck but pinion is not the part of three jaw chuck.

Which of the following is used to test Labelling of machine bed?

4. Which of the following is used to test leveling of machine bed? Explanation: Level of machine bed is generally tested by using sensitive spirit level in longitudinal and transverse direction. It is important that the machine should be installed truly in horizontal and vertical planes.

Which of the following is not the method of taper turning?

Which of the following is not the method of taper turning? Explanation: All are methods of taper turning.By using compound rest method and and attachment method, both internal and external taper can be turned while tailstock offset method is used only for external tapers.

What are the 5 major parts of a lathe machine?

The main parts of the lathe are:

• Headstock: The headstock is usually located on the left side of the lathe and is equipped with gears, spindles, chucks, gear speed control levers, and feed controllers.
• Tailstock: ...
• Bed: ...
• Carriage: ...
• Lead Screw. ...
• Feed Rod. ...
• Chip Pan. ...
• Hand Wheel.

What are the main parts of shaper?

Shaper Machine Parts:

• Base: It is the main body of the machine. ...
• Ram: It is the main part of the shaper machine. ...
• Tool head: It is situated at the front of the ram. ...
• Table: It is the metal body attached over the frame. ...
• Clapper box: It carries the tool holder. ...
• Column: ...
• Cross ways: ...
• Stroke adjuster:

What are the parts of drilling machine?

The basic parts of a drilling machine are a base, column, drill head and spindle. The base made of cast iron may rest on a bench, pedestal or floor depending upon the design. Larger and heavy duty machines are grounded on the floor. The column is mounted vertically upon the base.

What is shaper machine?

The shaper machine is a reciprocating type of machine basically used for producing the horizontal, vertical or flat surfaces. The shaper holds the single point cutting tool in ram and workpiece is fixed in the table. ... During the return stroke, No metal is cutting.

Which of the following operation can be performed in shaper?

4. Which of the following operation can be performed in shaper? Explanation: All mentioned operations can be performed in shaper. Although it is used mainly for producing flat surfaces but its a versatile machine and can be used for other purposes too.

What is shaping in manufacturing?

Shaping is a separate manufacturing process that, like planing, is designed to remove material from a workpiece. ... In shaping, the cutting tool rotates while the workpiece remains stationary. Shaping is used to change the size and shape of a workpiece. Like planing, it will remove material from the workpiece.

Which is the following is not part of the transmission system?

Which of the following is not a part of the transmission system? Explanation: Transmission system is used to transmit the power from engine to wheels. Transmission system consists of gears, and clutches to transmit the power at different gear ratios. Wheels are considered as a part of the automobile chassis.

Which one of the following is not an automobile?

Solution(By Examveda Team)

aeroplane is a powered, fixed-wing aircraft that is propelled forward by thrust from a jet engine, propeller or rocket engine.

What are the three shafts in a gearbox?

It has three shafts: the input shaft , the layshaft and the mainshaft, which run in bearings in the gearbox casing. There is also a shaft on which the reverse-gear idler pinion rotates. The engine drives the input shaft, which drives the layshaft.