You can also open the app and touch the banner that shows 'Aomais Go' and it will ping it that instant and report back the battery life. The Aomais Go reports its battery life in increments of 10% from 100% on down.

Also know, how do you tell if Aomais speaker is charging?

Red Light lit when charging Solid Red battery is fully charged Red light turn off when full charged Please make sure your Aomais GO battery has a sufficient charge, it is not able to connect when the charge is too low.

One may also ask, how do I reset my Aomais go? Amazon Customer.

press the vol up and down at the same time for a few seconds - you'll hear unpaird -

how do you change the language setting ?

I have the same problem and can't get any support.

Had the same problem on two of these.

This is not the issue.

My unit says its full.

Correspondingly, why is my Bluetooth speaker not charging?

If your Bluetooth speaker stops charging, there are two things involved; software issues or hardware issues. Software issues involve software bugs while hardware issues include an under-voltage lithium-ion battery, a bad micro USB cable, and a broken solder joint on the USB charging socket.

How do you fix a Bluetooth speaker that wont turn on?

Check the following if the portable wireless speaker won't turn on:

1. Make sure that your speaker has enough charge.
2. Make sure the USB AC adapter is connected to the speaker and the wall outlet firmly (not loose).
3. Press and hold the power button until the speaker makes a start-up sound.

Related Question Answers

How loud is the Aomais go?

Booming Bass and Full Volume – Get 30W sound with AOMAIS Go's two 15 watt full-range drivers and two passive radiators.

How do I pair Aomais u go?

Bring two AOMAIS SPORT II Speakers within 1m(3ft) of each other, then turn on each speaker. The BLUETOOTH indicator will flash slowly in blue and you will hear "powering on" &"ready to pair"; 2. Press and hold the 2 volume buttons at the same time of one speaker until you will hear a beep.

What makes a Bluetooth speaker Bluetooth?

Bluetooth speakers receive digital audio wirelessly via the Bluetooth protocol when paired with Bluetooth-enabled digital audio devices. BT speakers accept digital audio via BT wireless transmission; convert it analog audio; amplify it, and convert it into sound just as regular speakers would.

What is loudest Bluetooth speaker?

• New SOUNDBOKS. The loudest portable Bluetooth speaker on the market!
• The New SOUNDBOKS. 126 dB.
• Aiwa Exos-9. 100 dB.
• Bose S1 Pro Speaker System. 109 dB.
• Soundcore Trance. 101 dB.
• Turtlebox. 120 dB.
• DBSOARS Bluetooth Speaker. 97 dB.
• JBL Xtreme 2. 80 dB.

Can I use my Sony speaker while charging?

You can operate the speaker with the built-in battery by charging the speaker before use. The CHARGE indicator lights up in orange while charging. The estimated charging time differs depending on the power output capacity of the connected USB AC adaptor (commercially available).

How do I check the battery on my Bose speaker?

To check the charge level, press and hold the Power button and observe the battery indicator. The battery status LED will always be a half full battery symbol. You cannot check the remaining charge level of a battery that has entered protection mode.

How long does it take for Sony speaker to CHARGE?

It takes approximately three (3) hours for the built-in battery of the Bluetooth® speaker to charge from an empty state.

How do you know if JBL speaker is fully charged?

When you plug in your JBL Go 2 to your power source, the LED indicator will blink red. It will only turn off when your speaker is fully charged and ready to go. The well distinct sounds accompanied by an LED indicator lets you know when your device is connected, fully charged, paired, or powered on.

How do you troubleshoot a Bluetooth speaker?

The most likely cause for Bluetooth pairing difficulty is

1. Get your speaker and your audio device as close together as possible while you troubleshoot.
2. Reset the Bluetooth on your audio device (i.e. phone).
3. Next, reset the Bluetooth on your speaker. Then, you should be good to go.

How do you reset a Bluetooth speaker?

Press and hold the power and Bluetooth buttons simultaneously for several seconds until the indicator light turns red to white. Turn on the speaker and use it as you would a new speaker.

How do I know if my charger port is damaged?

How to Determine if your Phone Needs Charge Port Repair

1. Do you have to hold the phone at a certain angle to charge it?
2. You see some off-colored residue or debris around the charge port.
3. There is nothing wrong with the charger and battery.

Why is my Megaboom not charging?

To get your MEGABOOM back to a normal charging state, do the following: Connect your speaker to the charger and leave it connected for a few seconds. If the charge LED fails to pulse continuously, disconnect the cable from your speaker, then reconnect it, and leave it connected for a few seconds.

What does it mean when your JBL speaker won't charge?

If you notice your JBL speaker is not charging all the way, it is usually due to a fault with the charging port or the cable. Sometimes dust and debris can damage the charging port.

How can I charge my speaker without a charger?

You can operate the speaker by battery instead of the USB AC adaptor by charging the speaker before use.

1. Make sure that the speaker is turned off.
2. Connect the USB AC adaptor (supplied) to the micro-USB cable (supplied).
3. Connect the micro-USB cable to the DC IN 5V jack.
4. Plug the USB AC adaptor to an AC outlet.

Why isn't my Bose speaker charging?

If your Bose speaker isn't charging, it could be down to the battery, charging circuit, or charging port. If your speaker isn't holding a charge, it may need to be reset. If this fails to work, then the battery may need to be replaced.

How do I connect my JBL speaker to my echo?

Pair Your Phone or Bluetooth Speaker to Your Echo Device

1. Put your Bluetooth device in pairing mode.
2. Open the Alexa app .
3. Select Devices .
4. Select Echo & Alexa.
5. Select your device.
6. Select Bluetooth Devices, and then Pair A New Device.