Typically the punching mechanism is shielded by a metal plate, with a hole for the puncher to fit through. ... When the puncher is forced down, a crisp hole is punched in the paper. The pointed edges on the puncher make the first incisions for the hole, and the final downward motion completes the process.

How does a 3 hole punch work?

The punch lever is depressed, compressing the springs and causing the pins to move through the holes in the brackets and base. As the pins move through the holes, the paper is cut (or punched) where it was positioned above the holes. The bottom cover of the punch catches the circular pieces of paper cut by the pins.

Why do hole punches lock?

A hole punch that receives a lot of use can become locked up. Most often, one of those little paper discs gets lodged in the punch mechanism, causing the lever to no longer operate and jamming the paper punch.

Why does my hole punch not work?

If the barrel is not inserted into the coil or if any of the barrel casings have loosened, the punch will stop working. Remove the bottom punch holder. It is generally shaped as a plastic cover that overlaps onto the hole puncher. Make sure you remove this over a trash can.

What should a 3 hole punch be set at?

3-hole system

The 5⁄16 value is most commonly used, as it allows for looser tolerances in both ring binder and paper punching. The distance of the hole center to the paper edge also varies, with 1⁄2 inch (13 mm) being a typical value.

How To Use A Hole Punch

40 related questions found

How do you unstick two hole punches?

Grab a penny and place it between the 'jammed' puncher and place it between the bottom of the compressed spring and the washer. Grip your penny firmly and compress the washer in an upward motion until you hear a 'pop' sound. Your hole puncher is now unjammed.

How far in do hole punches go?

Most hole punches (whether you're punching two holes at the top or three holes on the side of the page) punch about 0.5 inches from the edge of the paper. We recommend measuring your punch or paper to make sure and maybe even making the margins just a bit bigger.

What can you use instead of a hole puncher?

Push pins, thick needles and nails may also be used to punch holes through paper, cardboard and other materials without nails. These items all create relatively narrow holes, which can be widened by placing a skewer through the hole once you puncture the project material.

Is it possible to punch a hole in paper?

You just have to punch fast enough, such that the inertia of the paper would allow for high enough tensions to build-up. This would tear the paper, instead of acceleration it up to the speed of your fist.

Who invented the hole puncher?

The first recorded patents for a paper hole puncher was published in 1885, when a man named Benjamin Smith invented spring-loaded hole puncher that had a receptacle to collect those little clips — Smith called it the “conductor's punch”.

What is a 2 hole punch for?

This two-hole punch can accommodate up to 28 sheets of standard 20-pound paper at once, letting you finish tasks faster. A chrome-plated adjustable guide on this Staples two-hole punch makes paper placement easy, and the attached chip tray catches paper bits to eliminate messes.

How are hole punches made?

Typically the punching mechanism is shielded by a metal plate, with a hole for the puncher to fit through. ... When the puncher is forced down, a crisp hole is punched in the paper. The pointed edges on the puncher make the first incisions for the hole, and the final downward motion completes the process.

What are the parts of puncher?

A punch press has two coacting components: the punch, which is attached to the reciprocating ram of the machine, and the die, which is clamped onto a bed or anvil whose flat surface is perpendicular to the path of the ram. In operation, the punch pushes against the workpiece, which is held in the die.

What should a two hole punch be set at?

see less Not with the hole punches set in their standard default positions. The punches can be re-positioned so that the two outer punches are 4.25 inches from center (the default standard position), 2.125 inches from center, or 1.375 inches from center.

How do you hole punch in the middle of a paper?

1. Choose your background paper. ...
2. Slide the small square of paper into your punch. ...
3. Place the punch and paper on the table. ...
4. Cut another square from your choice of coordinating paper. ...
5. Glue the coordinating paper to the piece with the punched shape. ...
6. Design your page and determine where you would like to use the punch.

Can you drill through cardboard?

Holes. For best results, we recommend using a drill bit and a cordless drill. You could also use manual cardboard cutting tools but it is hard to achieve a nice clean hole cut.

Can I hole punch laminated paper?

the laminating sheets are thinner than plastic sleeves. If I want a thicker finish I just use extra paper in between. Yes, you can use a 3 ring hole punch.

How do you use a single hole punch?

Place your punch over the marked circles, and cut the holes out. You can also place this over a few sheets that you want to hole punch. Use the guide to punch several papers at once. Repeat for all 6 holes.

Can you sharpen a hole punch?

Craft punches get dull after a while, but that doesn't mean they need to be replaced. Just grab a piece of aluminum foil; fold it over a few times; and take several punches out of it. The foil will sharpen the edges of the punch, so it works like new.

How do you unlock Swingline 3 hole punch?

Place the punch on a firm surface. Side facing you should be with the gray arrows. Hold down the punch arm and move the gray piece to the left. It will unlock.

Can you adjust hole puncher?

Adjust one hole at a time by turning the screw left. Slide the hole in the direction it should be, so the paper fits more easily into the binder. Punch another piece of scrap paper and test it in the binder to see if you're satisfied with the new location.